Power Rating

Minimum Rating
624.0 bhp
Maximum Rating
803.0 bhp

Engine Specifications

Aspiration
TA, TTA
Rotation (from flywheel end)
Counterclockwise
Stroke
7.2 in
Displacement
1106.0 in3
Configuration
In-Line 6, 4-Stroke-Cycle Diesel
Bore
5.7 in

Dimensions & Weights

Minimum Dry Weight
1950.0 lb
Maximum Width
44.6 in
Maximum Height
51.2 in
Maximum Length
73.0 in
Dry Weight
1950.0 lb
Length
73.0 in
Height
51.2 in
Width
44.6 in
  • AIR INLET SYSTEM
    • Separate circuit after-cooled (SCAC)
    • Open Crankcase Ventilation (OCV) system
    • Turbocharger, jacket water cooled
    • Turbocharger inlet, 152 mm (6 in) OD straight connection
  • CONTROL SYSTEM
    • Programmable low idle
    • Electronic diagnostics and fault logging
    • Electronic fuel/air ratio control
    • Engine Protection Mode for extended ambient conditions - EPA Tier 3 Ratings Only
    • 70-pin customer connector
    • Three types of throttle inputs (primary/ secondary PWM, 0-5V, 4-20mA
  • COOLING SYSTEM
    • Separate Circuit After-Cooling (SCAC) for both HEX and Keel cooled engines
    • Engine JW and SCAC Shell & Tube Heat Exchangers for HEX cooled engines
    • SCAC pump, gear driven, for HEX cooled engines only
    • Jacket water pump, gear driven
    • Auxiliary water pump, gear driven
    • Sea water pump, bronze impeller, gear driven
    • SCAC and JW shunt tanks for maintaining proper pump inlet pressures
  • EXHAUST SYSTEM
    • 152 mm (6 in) round flanged outlet
    • Water-cooled exhaust manifold & turbocharger
  • FLYWHEELS & FLYWHEEL HOUSINGS
    • Flywheel Housing, SAE No. 0
    • Flywheel, 18 inch, 136 teeth
    • SAE standard rotation
  • FUEL SYSTEM
    • Front service simplex fuel system
    • Fuel transfer pump, gear driven
    • Manual fuel priming pump
    • Hybrid fuel line design
  • LUBE SYSTEM
    • Front service simplex oil system
    • Array
    • Front and top service oil filler locations
    • Front service dipstick
    • Oil pump, gear driven
  • MOUNTING SYSTEM
    • Front support - adjustable
  • POWER TAKE-OFFS
    • Hydraulic Pump Drive
    • Crankshaft Pulleys
    • Front Stub Shaft
    • Front Enclosed Clutch
  • GENERAL
    • Front damper guard
    • Front service engine
    • Common electrical bonding point
    • Engine does not ship with zinc components
    • NOTE: These engines are for constant speed generator set applications only, and NOT to be used for variable speed applications
  • EXHAUST SYSTEM
    • Dry Elbows
    • Water-Cooled Elbows
    • Flexible Fitting
    • Flange
    • Muffler
    • Muffler Spark Arresting
  • AIR INLET SYSTEM
    • Air Inlet Adapter
  • CHARGING SYSTEM
    • Battery Chargers
    • Charging Alternators
    • Alternator Mounting Group
    • Ammeter
  • CONTROL SYSTEM
    • Array
    • Caterpillar Alarm and Protection
    • Load Sharing Attachment
  • COOLING SYSTEM
    • Aux Expansion Flange Kit
  • FUEL SYSTEM
    • Duplex Fuel Filters
    • Fuel Cooler
    • Primary Fuel Filters
    • Flexible Fuel Lines
  • INSTRUMENTATION
    • Array
    • OEM Wiring Harness
    • Gauges
    • Oil Level Sensor
  • LUBE SYSTEM
    • Duplex Oil Filters
    • Sump Pump
  • POWER TAKE-OFFS
    • Crankshaft Pulleys
    • Front Stub Shaft
    • Hydraulic Pump Drive Adapter
    • Front Enclosed Clutch
  • PROTECTION SYSTEM
    • Marine Classification Society and SOLAS
  • STARTING SYSTEM
    • Electric Starting Motors - Single 24 Volt
    • Air Starting Motor
    • Air Start Accessories
    • Starting Aids - JW Heaters
    • Battery Sets - 24 Volt - Dry
  • MOUNTING SYSTEM
    • Array
    • REAR ENGINE SUPPORT
  • PACKING
    • Engine Protective Cover
    • Storage Preservation
    • Export Packing
Get in touch Your Nearest Location
[contact-form-7 404 "Not Found"]
Two dads havin' fun.
Splishin' & splashin' in the hot summer sun.