Engine

Engine Model
Cat C9.3 ACERT™
Flywheel Power
215 hp
Displacement
567 in3
Net Power (Maximum) – 1,200 rpm: ISO 9249/SAE J1349
245 hp
Emissions
U.S. EPA Tier 4 Final
Net Power (Rated) – 2,200 rpm: ISO 9249/SAE J1349
215 hp
Note
All non road Tier 4 diesel engines are required to use only Ultra Low Sulfur Diesel (ULSD) fuels containing 15 ppm (mg/kg) sulfur or less. Biodiesel blends up to B20 (20% blend by volume) are acceptable when blended with 15 ppm (mg/kg) sulfur or less ULSD
Note
Diesel Exhaust Fluid (DEF) used in Cat Selective Catalytic Reduction (SCR) systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241.
Build Number
19

Service Refill Capacities

Fuel Tank
97.2 gal
Cooling System
12.2 gal
Engine Crankcase
6.5 gal
Power Train
39.1 gal
Final Drives (each)
3.6 gal
Hydraulic Tank
16.5 gal
Roller Frames (each)
6.6 gal
Pivot Shaft Compartment
1.3 gal
DEF Tank
4.5 gal

Weights

Operating Weight
47138 lb

Operating Weight

XL A
47846 lb
XL SU
47138 lb
XL VPAT
53042 lb
XW A
49797 lb
XW SU
48909 lb
XW VPAT
54045 lb
LGP S
51385 lb
LGP A
53829 lb
LGP VPAT
54526 lb
Note
Operating weight includes blade, lubricants, coolant, full fuel tank, standard track, ROPS/FOPS cab, drawbar and operator.

Blades – Capacity

XL SU-Blade
7.26 yd3
XL A-Blade
5.17 yd3
XL VPAT-Blade
6.07 yd3
XW SU-Blade
7.38 yd3
XW A-Blade
5.69 yd3
XW VPAT-Blade
6.57 yd3
LGP S-Blade
4.96 yd3
LGP A-Blade
6.46 yd3
LGP VPAT-Blade
6.57 yd3

Dimensions – XL

Width of Tractor Without Trunnions (standard track)
8.00 ft
Machine Height to Product Link Antenna(1)
10.67 ft
Length of Track on Ground
9.25 ft
Length of Basic Tractor(2)
13.83 ft
Ground Clearance
15 in
Ground Pressure (ISO 16754)(3)
8.66 psi
Note
(1) Height measured from ground line. Add grouser height for total dimension on hard surfaces. When Cat GRADE with 3D antennas are installed, overall machine height increases by approximately 82 mm (3.2 in).
Note
(2) Add 218 mm (9 in) for drawbar. Add 1387 mm/1291 mm (4'7"/4'3") for ripper on short track roller frame and long track roller frame machines respectively.
Note
(3) All dimensions above with Heavy Duty undercarriage. XL and XW with SU blade, LGP with S blade with no rear attachments unless otherwise specified and calculated per ISO 16754.

Dimensions – XW

Width of Tractor Without Trunnions (standard track)
9.17 ft
Machine Height to Product Link Antenna(1)
10.67 ft
Length of Track on Ground
9.25 ft
Length of Basic Tractor(2)
13.83 ft
Ground Clearance
15 in
Ground Pressure (ISO 16754)(3)
6.64 psi
Note
(1) Height measured from ground line. Add grouser height for total dimension on hard surfaces. When Cat GRADE with 3D antennas are installed, overall machine height increases by approximately 82 mm (3.2 in).
Note
(2) Add 218 mm (9 in) for drawbar. Add 1387 mm/1291 mm (4'7"/4'3") for ripper on short track roller frame and long track roller frame machines respectively.
Note
(3) All dimensions above with Heavy Duty undercarriage. XL and XW with SU blade, LGP with S blade with no rear attachments unless otherwise specified and calculated per ISO 16754.

Dimensions – LGP

Width of Tractor Without Trunnions (standard track)
10.50 ft
Machine Height to Product Link Antenna(1)
10.83 ft
Length of Track on Ground
10.67 ft
Length of Basic Tractor(2)
14.50 ft
Ground Clearance
16 in
Ground Pressure (ISO 16754)(3)
5.11 psi
Note
(1) Height measured from ground line. Add grouser height for total dimension on hard surfaces. When Cat GRADE with 3D antennas are installed, overall machine height increases by approximately 82 mm (3.2 in).
Note
(2) Add 218 mm (9 in) for drawbar. Add 1387 mm/1291 mm (4'7"/4'3") for ripper on short track roller frame and long track roller frame machines respectively.
Note
(3) All dimensions above with Heavy Duty undercarriage. XL and XW with SU blade, LGP with S blade with no rear attachments unless otherwise specified and calculated per ISO 16754.

Dimensions – XL VPAT

Width of Tractor Without Trunnions (standard track)
8.92 ft
Machine Height to Product Link Antenna(1)
10.67 ft
Length of Track on Ground
9.25 ft
Length of Basic Tractor(2)
16.08 ft
Ground Clearance
15 in
Ground Pressure (ISO 16754)(3)
9.78 psi
Note
(1) Height measured from ground line. Add grouser height for total dimension on hard surfaces. When Cat GRADE with 3D antennas are installed, overall machine height increases by approximately 82 mm (3.2 in).
Note
(2) Add 218 mm (9 in) for drawbar. Add 1387 mm/1291 mm (4'7"/4'3") for ripper on short track roller frame and long track roller frame machines respectively.
Note
(3) All dimensions above with Heavy Duty undercarriage. XL and XW with SU blade, LGP with S blade with no rear attachments unless otherwise specified and calculated per ISO 16754.

Blades – Width

XL SU-Blade
10.7 ft
XL A-Blade
13.7 ft
XL VPAT-Blade
12.7 ft
XW SU-Blade
11.7 ft
XW A-Blade
14.8 ft
XW VPAT-Blade
13.7 ft
LGP S-Blade
13.3 ft
LGP A-Blade
16.6 ft
LGP VPAT-Blade
13.7 ft

Dimensions – XW VPAT

Width of Tractor Without Trunnions (standard track)
9.83 ft
Machine Height to Product Link Antenna(1)
10.83 ft
Length of Track on Ground
10.67 ft
Length of Basic Tractor(2)
16.42 ft
Ground Clearance
16 in
Ground Pressure (ISO 16754)(3)
6.92 psi
Note
(1) Height measured from ground line. Add grouser height for total dimension on hard surfaces. When Cat GRADE with 3D antennas are installed, overall machine height increases by approximately 82 mm (3.2 in).
Note
(2) Add 218 mm (9 in) for drawbar. Add 1387 mm/1291 mm (4'7"/4'3") for ripper on short track roller frame and long track roller frame machines respectively.
Note
(3) All dimensions above with Heavy Duty undercarriage. XL and XW with SU blade, LGP with S blade with no rear attachments unless otherwise specified and calculated per ISO 16754.

Dimensions – LGP VPAT

Width of Tractor Without Trunnions (standard track)
10.33 ft
Machine Height to Product Link Antenna(1)
10.83 ft
Length of Track on Ground
10.67 ft
Length of Basic Tractor(2)
16.42 ft
Ground Clearance
16 in
Ground Pressure (ISO 16754)(3)
6.28 psi
Note
(1) Height measured from ground line. Add grouser height for total dimension on hard surfaces. When Cat GRADE with 3D antennas are installed, overall machine height increases by approximately 82 mm (3.2 in).
Note
(2) Add 218 mm (9 in) for drawbar. Add 1387 mm/1291 mm (4'7"/4'3") for ripper on short track roller frame and long track roller frame machines respectively.
Note
(3) All dimensions above with Heavy Duty undercarriage. XL and XW with SU blade, LGP with S blade with no rear attachments unless otherwise specified and calculated per ISO 16754.
Get in touch Your Nearest Location
[contact-form-7 404 "Not Found"]
Two dads havin' fun.
Splishin' & splashin' in the hot summer sun.